Kirin leaf is also known as the unicorn tail, the upper tree dragon, and the flying dragonfly. It is a perennial evergreen vine and foliage plant of the genus Tetranychus. Kirin leaves are large vines with large stems, large roots, and strong climbing ability. Young leaves narrowly lanceolate or lanceolate; oblong. Mature leaves are pinnately lobed, reaching midvein, with holes on both sides of the midvein, leaf length 20-30 cm, width 15-18 cm. The unicorn leaves originate from the provinces of Guangdong, Guangxi, Hainan and Taiwan in the south of China, and India and Malaysia. The sex likes warm, moist and dark surroundings. It is slightly tolerant to drought, and it has a hard-weathered, hard-weathered, hard-to-soil requirement. It is a fertile loam with good drainage. Kirin leaf multiplication with cuttings. Generally in the growing season to cut stem section 2-3 sections (with 1-2 leaves), cut half of the leaves to reduce evaporation; then insert the semi-mature substrate of river sand and rot leaf, shade insulation. At a temperature of 20-25°C, rooting can take place within 1-2 weeks. Plants shed on the lower leaves of old plants can be dwarfed and replaced by cuttings. Kirin leaf pot can be used 2 parts of rot leaf soil, 1 part of garden soil mixed as a substrate. Add a small amount of base fertilizer when planting. First, insert a pack of brown skin in the pot, plant 3-4 seedlings around the pot, and let it climb along the column. Because of its large leaves and sparse foliage, it is advisable to adjust its stems when planting, so that the stems are wrapped around the front of the column, and the bundles are fixed so that the distribution of stems is more reasonable and a good plant shape is guaranteed. It is also possible to plant a cliff without pillars. Water should be fully grown during the growing season, and the basin should be kept moist; when the climate is dry, water should be sprayed to the foliage and uprights to maintain high air humidity, which is conducive to aerial root growth and plant growth. After the end of the fall, the temperature is low and the basin soil should not be too high. Wet, to keep the inter-dry wet. During the growing season, apply 2-3 liquid fertilizers every month. Note that the fertilization should not be too thick so as to avoid fertilizer damage. Because of its thin leaves and strong negative resistance, the entire growth period must be placed in a semi-negative environment, especially in the summer to avoid direct sunlight, otherwise the leaves are easily burned. Kirin's stems are stout and sturdy. The leaves are large and deep-seated, and the leaves are dark green and glossy. They are quite elegant foliage plants. Because of its strong resistance to negatives, strong root absorption, and rapid growth, it is suitable for cultivation of climbing plants. It can be used as a vertical greening material, which is worth appreciating. The unicorn leaves, also known as unicorn's tail, are the evergreen vines of the Araceae, with large stems and large leaves with roots. The leaves are feather-like, with several mid-veins and small holes on both sides of the midrib. They are good foliage plants. This plant is native to the southern coastal provinces of China and India, Malaysia and other countries. Hi warm and humid environment, tip drought, strong negative resistance, afraid of the hot sun, should be half-yin, strict requirements on the soil. Suitable for use in fertile soils rich in humus. Kirin leaf conservation management is relatively simple, after the spring out of the house under the arbours or near the indoor window, to avoid direct sunlight. Usually watered to keep the soil moist. When the temperature is low, it is necessary to control the pouring, and the soil need not be too moist. During the growth period, 2-3 thin fertilizers are applied every month; when the weather is dry, the plants should be sprayed with water and humidified. Because it has a sucker root, a beautiful form, and a fast growth, it is suitable for cultivation as a climbing plant, which is quite appreciated. During the cultivation, first insert the brown-wrapped wood column or the stump better in the pot. Because of its thick stems, the leaves are large and thin. When planting, the plants should be on the back of the brown wood column or stump, and then the vines should be made. Surround the front, artificially adjust it and fix it with banding to make it more reasonable and better. After entering the room in the early winter, the room temperature should not be lower than 0°C, and watering should be controlled. Kirin leaf breeding more cutting method. The method is: Take 2-3 stems in the growing season, with 1-2 leaves. Because of its large leaves, the leaves should be cut in half, and then inserted into the sand or vermiculite, shading moisture, it is easy to take root. Water can also be inserted. Plants that have fallen off from the lower leaves of old plants can be dwarfed and replaced by cuttings.
ETR has independently developed an integrated vacuum pump unit composed of a water-ring vacuum pump, a gas-water separator, a vacuum solenoid valve, pipe fittings and an electrical control system. It is a simple, safe and reliable device that continuously serves the wards all day long, without occupying the ward space. The negative pressure is sourced from the vacuum pump unit.
Cabinet Vacuum Suction Unit Cabinet Vacuum Suction Unit,Central Suction Station,Negative Pressure Suction Unit,Negative Pressure Suction Station Hunan Eter Electronic Medical Project Stock Co., Ltd. , https://www.centralgas.be